Electric Graver-Type 1

• Product Name:

  Electric Graver-Type 1

• Category: Others
• Price: Get Latest Price

• Product Detials: 

  Instruction

  1.       Do not touch the hot using handle

  2.       Do not touch with wet hand

  3.       Create a correct circuit in the instrument in order to avoid mechanical failure caused by shock or stress.

  4.       If there is any problem about malfunction or further information, please contact us

  5.       While changing the electric moulding chip, please cut off the power. Chang it when it is cold to avoid burning.

  6.       Watch out for the chip. Do not touch the wire in order to prevent from fire .

  7.       Do not use damaged or broken power brake, embolism or loose nut (otherwise, it may cause fire or electric shock).

  8.       Do not move the power brake. Do not put heavy object on it.(otherwise, it may cause fire or electric shock)

  9.       Warn:In order to avoid the danger of getting a shock, the instrument should be connected with the ground wire.

  10.   Do not jam the intake that on the bottom of the product (otherwise,it may cause fire).

  11.   Cut the power off ,if the instrument is not used for a long time or it is lightening and thundering.

  12.   Do not get the embolism out, nip on part of the power brake. Do not touch it with wet hand (otherwise ,it may cause fire or electric shock).

  13.   Do not assemble the instrument in a place,where theres high humidity, lots of dust or water on the ground

  14.   Please set it up on a spot, where there is no heat resource device.

  15.   Please wash this product after cutting off the power. Do not sprinkle it directly or use chemical medicine to clean it (otherwise, it may cause fire or)

  16.   Please move away the dust and water drops on the power brake bolt (otherwise ,it may cause fire or electric shock ).

  17.   Cut the power off, if there is any noise , strange smell or smoke (otherwise, it may cause fir or electric shock).

  18.   Do not dismantle, mend or reassemble the instrument by yourself (otherwise ,it may cause electric stock)

  If do not operate as the instruction of the manufacturer, the safety of the instrument will be weakened..

  Environment condition:

  Inner operation

  Temperature 5-40

  Humidity:minimum50,maximum80

  Valtage of power supplyminimum voltage range ±10

  Pollution grade :2

  Instuction

  The instrument is specially designed for the electric moulding wax mold. It is featured with accurate waxing technique, changeable moulding chip and manageable temperature.

  Function and feature

  1.    Good heat exchange, long service life, easy to operate

  2.       Visible control button, easy operation

  3.       2loops working together

  4.       Invariable direct current voltage, stable temperature

  5.       Control the temperature accurately and redesign function. Long service life and high heat exchange .

  6.       Good visible control button ,convenient to operate , LEDindicator

  7.       Using digital processor loop to maintain the accuracy of set temperature

  8.       Using digital visible temperature, degree Celsius or Fahrenheit

  9.       The previous working temperature can be recorded affer cutting off the power.

  10.   Press the pad button, the signal will come out

  11.   On-off power is very handly. 100-240V alternating current is available and no need to adjust again. Long service life is its feature.

  12.   Silicon handle can release the fatigue of operating for long time.

  Instruction

  1.    Insert the plug of power(support the alternating current 100-240V),insert heating pen of wax knife to OUT1/OUT2.

  2.       Press the button POWER,the green light will be lightened.

  3.       Open (the digital indicator ),press switch ON/OFF.

  4.       Set up the prearranged temperature respectively, /(press once is for increasing or reducing the temperatur for one degree, press steadily for 1∼2 seconds, the temperature will be increased or reduced very rapidly).

  5.       Press the button to choose degree Celsius or Fahrenheit, press the button C/T in the lower right corner.

  6.       If there is error, there is signal sound.The mistake will be displayed in the window. Turn off the switch to get rid of the sound. Turn on the ON/OFF button again.

  Instruction

  1.    Insert the wax moulding pen, turn on the power switch (light is on),(DENSTAR-110/120).

  2.       Turn on ON/OFF button (green light is on),(DENSTAR-140).

  3.       Press the ON/OFF button (green light is on),(DENSTAR-110/120).

  4.       Push ON/OFF button (FND digital indicator),(DENSTAR-110)

  5.       Insert anticipated chip into OUT1/OUT2.(DENSTAR-110) insert anticipated chip into OUT.(DENSTAR-140)

  6.       Set up anticipated temperature .Refer to the temperature indication.

  7.       Set up temperature, use button up/down (press one time to increase or reduce the temperature by 1 degree.Press it continuously to increase or reduce temperature rapidly),(DENSTAR-110/140).

  8.       Memory function: remember the previous work temperature with or without power.Press M1(M2) for 5 seconds after setting up the anticipated temperature or usual temperature . Set anticipated temperature in M1(M2) when the digital signal beeps.(DENSTAR-140)

  9.       Press the button to choose degree Celsius or degrees Fahrenheit(display / on FND window).(DENSTAR-110/140)

  10.   If there is error, sifnal sounds. The error displays in DENSTAR-110/140FND window. Turn off the switch to get rid of the signal sound, and then press the ON/OFF button again.

  11.   Instrnction of indication temperature.(DENSTAR-140)

  Target

  Temperature                  20-200(122-392)

  Input power source           50/60HZ

  Power                        20W

  Insurance current            2A

  Dimension

  Weight                       1.27KG

  Width                        199MM

  Depth                        159MM

  Height                       73MM